Product | Volt | Weight max per leaf |
Angle max per leaf |
Width max per leaf |
Type | Price | Buy |
---|---|---|---|---|---|---|---|
Proteco Kit Leader 3Ti (Left) | 24V |
270KG |
110° |
2m |
Linear Ram, Left |
£524.48+vat
|
|
Proteco Kit Leader 4Ti (Left) | 24V |
250KG |
110° |
2.5m |
Linear Ram, Left |
£534.64+vat
|
|
Proteco Kit Leader 5Ti (Left) | 24V |
150KG |
110° |
3m |
Linear Ram, Left |
£497.61+vat
|
|
Proteco Kit Leader 3Ti (Right) | 24V |
270KG |
110° |
2m |
Linear Ram, Right |
£524.48+vat
|
|
Proteco Kit Leader 4Ti (Right) | 24V |
250KG |
110° |
2.5m |
Linear Ram, Right |
£534.64+vat
|
|
Proteco Kit Leader 5Ti (Right) | 24V |
150KG |
110° |
3m |
Linear Ram, Right |
£547.37+vat
|
|
Need this kit in 230v? Click here
The Kit Leader has proven reliabilty at an affordable price.
The Kit Leader comprise 3 kit options covering almost all residential & agricultural double swing gate dimensions.
The rams are non-reversible and therefore don’t need the inconvenience or expense of an additional electric lock to keep them closed.
The 24V version is suitable for intensive use and it can be equipped with a backup battery in case of power cut. Click here to buy.
Limited Warranty - 3 years on motors, 1 year on other components. See T&C's for more info.
The Kit Leader has linear ram (straight arm) motors which mount on brackets (highlighted in yellow below) attached to the pillars.
For optimum leverage and mechanical advantage the motors must be mounted where the A & B measurements (shown below) are equal.
For optimum leverage and mechanical advantage the motors should be mounted where the A & B measurements are equal as per table below:
Recommended Installation (90° opening)
A + B = C (motor Stroke)
A |
B |
C |
|
Kit Leader 3TI |
150mm | 150mm | 300mm |
Kit Leader 4TI |
200mm | 200mm | 400mm |
Kit Leader 5TI |
250mm | 250mm | 500mm |
If the ideal scenario of A & B is not achievable, refer to the below table to determine bracket position. (mm)
The D dimension only comes into play when the gate is side hung.
Leader 3TI max D measurement = 150mm
Leader 4TI max D measurement = 200mm
Leader 5TI max D measurement = 225mm
Before purchasing this kit it is important to note the width of your post/pillar and hinge position.
Your post/pillar must be wide enough to fix the bracket so the A & B measurements can be achieved for the motor you require.
The motor is usually mounted on the inside of the property for security. With this in mind view the gates from inside the property looking outwards (the gates will normally, swing toward you). If the hinge appears on the left, you need a left-hand kit; if it's on the right you need a right-hand kit.
When fitting the gate brackets to a wooden gate, we recommend that you insert stainless steel tubing (just large enough to sleeve the mounting bolt threads and 1mm shorter than the thickness of the wood) through the gate mounting holes. This will prevent over-tightening of the mounting bolts and also avoid the repetitive push/pull on the mounting bolts from damaging the wood - See the instruction manual under the download section on this page for more information.
These electric gate motors require a physical stop at the end of the opening and closing cycle. Gate Stops provide resistance to the motors so they know they've reached either the open or closed position. Without gate stops the motors will over extend during their operation and the mechanism will eventually fail. When assessing your gate-way it is important to check you can install physical stops in both the closing and opening positions. Common reason's why gate stops cannot be installed are a sloping driveway or the gate is raised significanlty off the ground. If you cannot install something to provide resistance at either end of the motors cycle then you will require a specialised ram with in-built mechanical stops.
Need more information or advice on this kit ? Call our sales support team on 01202 717 191 or complete our site assessment form and we can advise the right kit for your installation.