Call us on: 01202 717 191

Nice TT2 Miniaturised Control Unit

Image for Nice TT2 Miniaturised Control Unit

Kit Contents

1 x Nice TT2 Control Board
Product Details Price Buy
Nice TT2D Miniaturised control board
TT2D Control unit for management of 230 Vac lighting systems, with built-in radio receiver and switching module
£70.00+vat

£84.00 inc.vat

Nice TT2N Miniaturised control board
TT2N Control unit for 230 Vac motor with built-in radio receiver
£65.74+vat

£78.89 inc.vat

Nice TT2L Miniaturised control board
TT2L Control unit for management of 230 Vac lighting systems, with built-in radio receiver
£66.00+vat

£79.20 inc.vat

Mindy TT, miniaturised control units compatible with Era and NiceWay series transmitters.
Maximum flexibility: can memorise up to 30 transmitters in Mode I and Mode II.


Fast programming
thanks to the programming button. A Led indicator helps the user to follow the correct programming procedure, for example signalling when the set thresholds of the climatic sensor are exceeded.

Possibility of connection to climate sensors Nemo and Volo S-Radio.

IP20 Protection level.

TT2N, radio receiver and control unit for 230 Vac motor up to 500 W.

 

Possibility of connecting a push button for cable control in mode STEP-BY - STEP - ALWAYS UP - ALWAYS DOWN

Possibility of memorizing radio controls in

Mode I: UP - STOP - DOWN - "HOLD-TO-RUN" DOWN

Mode II: STEP-BY-STEP - UP STOP - DOWN STOP - STOP -  "HOLD-TO-RUN" DOWN - "HOLD-TO-RUN" UP

 

TT2L, radio receiver and control unit for lighting systems.

For the control of 230 Vac mains voltage loads with power up to 1000 W / 500 VA.

Simplified connections thanks to the switch connected directly to the power mains (not for TT2D).

The connection to the Niceway Sensor enables management of light activation and shutdown by the twilight switch function.

Programmable timer from a minimum of 0.5” to a maximum of approx. 9 hours; optimised programming procedure, maintaining set values also in the event of a power failure.

TT2D, radio receiver and control unit for lighting systems from multiple points, with switching module.

Same characteristics as TT2L

 

 

Technical Specifications

Code TT2L TT2D TT2N
Power supply (Vac/Hz) 120 or 230 Vac, 50/60 Hz, limits: 100÷255 Vac
Maximum motor power

500 VA for Vn = 230 V,

600 VA for Vn = 120 V

1000 W / 500 VA for Vn = 230V,

600W/600VA for Vn = 120V

Protection rating (IP) 20
Manoeuvre duration (sec)

4÷240 s

(factory setting approx. 150 s)

1 s ÷ 9 h

(factory setting TIMER1= 1 min, TIMER2= 10 min)

Working temperature (°C Min. Max.) -20 ÷ +55
Dimensions (mm) 40 x 18 x 32
Weight (g) 20
Frequency (MHz) 433.92

Gate Automation

Please select what type of automation you require for your gate/s. Double & Single Swing refer to motors which attach to the gate and pillar of a swing motion gate. Double & Single Underground refer to motors which lay beneath the ground which attach to the hinge end of swing motion gates. Choose Sliding if you require lateral moving gate automation and Wheeled if you require a motor which utilises a wheeled motor to drive your gate/s.

Motor Voltage

There are two types of power outputs to consider - 24v & 230v. If you need a higher number of operations (opened/closed more than 5-6 times in an hour) during peak periods such as the morning and evening, then you may wish to consider a 24v system.

24v systems are more suitable for higher operation levels as they tend to run cooler than 230v gate motors. However, they do cost more in relative terms, so if you only need to open or close the gate 1-5 times an hour then a 230v system might prove more cost-efficient.

24v motors tend to be used on commercial premises, whereas 230v tend to be used on standard domestic properties. The exception to this rule is sliding gate motors where the reverse is true - 24v sliding gate automation systems tend to be for domestic use, 230v for more intense use (commercial/communal).

24v systems can draw power from battery backup systems meaning they can still operate during any mains power cut (a 230v or 3 phase system would need to be opened with a manual release key).

24v systems can also utilise solar power units as a means of charging batteries, allowing you to site gate automation in rural and remote locations where mains power is unavailable.

Specifications can be found for each product from their datasheet. Each datasheet is downloadable from each product page on this website.

Weight of Gate

All electric gate motors operate up to a maximum weight. This is so the gate will operate in a reliable and safe manner. It is essential to know the weight of each gate leaf in order to choose the correct motor for you installation. If you do not know the weight of your gate/s, send us a photo along with the gate/s dimensions and we can advise.

Gate Width

As with weight, gate motors are designed for gates within certain dimensions. The most important dimension is the width of the gate. To ensure you select the right motor to operate your gate you must know the width of each gate that requires automation.

Opening Angle

Each motor has a maximum angle to which it can operate to. Therefore it is important to note how far the gate needs to open in order for a vehicle to enter/exit safely.

Daily Use

The amount of times your gate is used per day is a determining factor when deciding on the right motor for your usage. Motors are designed to operate within a certain capacity (operations per day) so choosing a motor compatible with your desired use is essential for its durability. Select from the options below the number of times (open & closure = 1 x operation) the gate/s will be operated on an average day.