Call us on: 01202 717 191

Nice OX4T Universal 4 Channel Receiver

Image for Nice OX4T Universal 4 Channel Receiver

Kit Contents

1 x Nice OX4T Universal 4-Channel Receiver
Product Details Price Buy

Nice OX4T Universal 4-channel Receiver
OX4T Universal 4-channel receiver with built-in transmitter
£90.00+vat

£108.00 inc.vat

Universal 4-channel receiver in the One series, with built-in transmitter.

Equipped with BUS T4 connector for connection to O-View. For remote control of any automation on gates, garage doors, road barriers, shutters, awnings, venetian blinds, irrigation and lighting systems or other electrical circuits.

Compatible with encoding systems O-Code, TTS, FloR, Smilo and Flo.

OX4T manages 4 outputs controlled by 4 relays, usable as power relays or voltage-free contacts, to extend use of the Opera system also to devices with specifi c provisions.

Controlled by the same transmitter, all automations for gates, garage doors barrier gates, shutters, awnings and other current loads, also with timer options. The output relays can be associated with specifi c functions for the control of Venetian blinds.

OX4T can be connected via radio to the interface O-Box and via BUS T4 to the multifunction display O-View, to enable programming, diagnostics, timed functions and management of codes, also remotely by means of the modules OVBT and OVBTGSM.

Thanks to the internal transmitter, OX4T can be used as a repeater, thereby increasing the operating range between transmitters and other receivers in the One series.

2 programming modes: “Mode I” and the new “extended Mode II” which enables expansion of the number of controls to up to 14.

Multicode: OX4T is also compatible with the transmitters with encoding system O-code, Smilo Flo, FloR, FloR and TTS with or without self-learning, for multicode transmission, which enables the delivery of simultaneous commands from a single transmitter.

OX4T is fitted with removable terminals to facilitate connections and a generously sized memory to enable storage of up to 1024 transmitters, with the option for password protection.

Technical Specifications

Power supply (Vac 50/60 Hz) 110 ÷ 240
Maximum absorbed current (mA) 80
Encoding O-Code / TTS / FloR (rolling code); or Smilo (rolling code) or Flo
Frequency (MHz) 433.92
Antenna impedance (ohm) more than 0.5 for successful signal
Estimated range (m) 200 in open spaces / 35 if inside buildings
Radiated power (dBm) +2
Max. capacity of transmitter memory 1024 (maximum)
Outputs 4 relays with NO and NC contacts, voltage-free
Contact capacity 5 A - 250 V
Timer times programmable from 2 seconds to 540 minutes
Protection rating (IP) 44 (with container intact)
Working temp. (°C Min/Max) from -20° to +55°
Dimensions (mm) 128 x 112 x 43 h
Weight (g) 260

Gate Automation

Please select what type of automation you require for your gate/s. Double & Single Swing refer to motors which attach to the gate and pillar of a swing motion gate. Double & Single Underground refer to motors which lay beneath the ground which attach to the hinge end of swing motion gates. Choose Sliding if you require lateral moving gate automation and Wheeled if you require a motor which utilises a wheeled motor to drive your gate/s.

Motor Voltage

There are two types of power outputs to consider - 24v & 230v. If you need a higher number of operations (opened/closed more than 5-6 times in an hour) during peak periods such as the morning and evening, then you may wish to consider a 24v system.

24v systems are more suitable for higher operation levels as they tend to run cooler than 230v gate motors. However, they do cost more in relative terms, so if you only need to open or close the gate 1-5 times an hour then a 230v system might prove more cost-efficient.

24v motors tend to be used on commercial premises, whereas 230v tend to be used on standard domestic properties. The exception to this rule is sliding gate motors where the reverse is true - 24v sliding gate automation systems tend to be for domestic use, 230v for more intense use (commercial/communal).

24v systems can draw power from battery backup systems meaning they can still operate during any mains power cut (a 230v or 3 phase system would need to be opened with a manual release key).

24v systems can also utilise solar power units as a means of charging batteries, allowing you to site gate automation in rural and remote locations where mains power is unavailable.

Specifications can be found for each product from their datasheet. Each datasheet is downloadable from each product page on this website.

Weight of Gate

All electric gate motors operate up to a maximum weight. This is so the gate will operate in a reliable and safe manner. It is essential to know the weight of each gate leaf in order to choose the correct motor for you installation. If you do not know the weight of your gate/s, send us a photo along with the gate/s dimensions and we can advise.

Gate Width

As with weight, gate motors are designed for gates within certain dimensions. The most important dimension is the width of the gate. To ensure you select the right motor to operate your gate you must know the width of each gate that requires automation.

Opening Angle

Each motor has a maximum angle to which it can operate to. Therefore it is important to note how far the gate needs to open in order for a vehicle to enter/exit safely.

Daily Use

The amount of times your gate is used per day is a determining factor when deciding on the right motor for your usage. Motors are designed to operate within a certain capacity (operations per day) so choosing a motor compatible with your desired use is essential for its durability. Select from the options below the number of times (open & closure = 1 x operation) the gate/s will be operated on an average day.