Call us on: 01202 717 191

Kit myDiamond - Double Electric Swing Gate Opener Kit

Product Volt Weight
max
per leaf
Angle
max
per leaf
Width
max
per leaf
Type Price Buy
Kit myDiamond 3TI
230v
350kg
110°
2.0m
Linear Ram
£475.00+vat
RRP £712.50 Save 20%

£570.00 inc.vat
Kit myDiamond 4TI
230v
400kg
120°
3.0m
Linear Ram
£490.00+vat
RRP £735.00 Save 20%

£588.00 inc.vat

Kit Contents

2 x Motors
2 x Wired Safety Photocells
1 x Control Board (with in-built aerial)
2 x Radio Remotes
4 x Brackets with fixings & fittings
2 x Manual Release Keys
1 x Instruction Sheet

 

 

The GateMotors Kit myDiamond electromechanical ram kits combine quality performance and sleek design at a competitive price.

The myDiamond is powerful, quiet and compact.

Opening angles of up to 120° are achievable with this kit but will rely on specific hinge positioning (see instruction manual for more information).

This kit is suited to gates up to 3.5m (per leaf) and maximum gate weight of up to 400Kg (per leaf).

The myDiamond motors are constructed of quality die-cast aluminium with stainless steel, bronze and steel parts. It also has inbuilt limit stops (on closing) therefore removing the need for a mid-stop. The motors are also non-reversible and therefore don’t need the inconvenience or expense of an additional electric lock to keep them closed.
The fluid-grease lubrication system, polyester powder-paint coating, self-lubricating worm gear and built-in thermal protection system ensure quiet operation and a long working life in all weather conditions, without the need for periodic maintenance.

Quick and simple to install, it can easily fit on almost any kind of swing gate.

The myDiamond motor is only suited to inward opening gates. 

 

Product Details

myDiamond 3TI

myDiamond 4TI

Opening time

17 seconds

22 seconds

Frequency of use

Ideally less than 15

operations a day

Ideally less than 15

operations a day

Opening direction

Inwards only

Inwards only

IP rate

44

44

Inbuilt aerial range

30m

30m

Extra safety cells required

Additional photocells recommended

Additional photocells recommended

Limited warranty (Motor)

3 Years

3 Years

 

Gate Mounting

With all linear ram (straight arm) motors it is essential to mount the brackets correctly for efficient operation and durability of the equipment.

The ideal geometry for a ram is where A = B (as shown in the diagram below) as the leverage and mechanical advantage in all phases of opening and closing are equal.

This will also result in the lowest amount of stress on the ram, hinges and ram mountings - hinges must be plumb!

Pillar/Gate Bracket Mounting

To achieve optimum leverage and efficiency the gate opener needs to meet the following parameters (within 10mm tolerance) - measurements are taken from the pillar bracket to the gate bracket when gate is in closed position:

 

myDiamond 3TI

myDiamond 4TI

A 145mm 195mm
B 145mm 195mm
D 150mm (Max) 200mm (Max)

 

Installation Advice

When fitting the gate brackets to a wooden gate, we recommend that you insert stainless steel tubing (just large enough to sleeve the mounting bolt threads and 1mm shorter than the thickness of the wood) through the gate mounting holes. This will prevent over-tightening of the mounting bolts and also avoid the repetitive push/pull on the mounting bolts from damaging the wood.

 

Need more information or advice on this kit ? Call our sales team on 01202 717 191.

 

myDiamond optional upgrades and accessories include:
gate stops (all of our gate motors require some form of resistance at the end of the opening & closing phase.)
underground exit loop (detects the presence of a vehicle and automatically opens the gate)
extra photocells
additional key fobs
intercom kit
extended range (external) aerial

 

Products bought with Kit myDiamond - Double Electric Swing Gate Opener Kit

Kit Contents

2 x Motors
2 x Wired Safety Photocells
1 x Control Board (with in-built aerial)
2 x Radio Remotes
4 x Brackets with fixings & fittings
2 x Manual Release Keys
1 x Instruction Sheet

Gate Automation

Please select what type of automation you require for your gate/s. Double & Single Swing refer to motors which attach to the gate and pillar of a swing motion gate. Double & Single Underground refer to motors which lay beneath the ground which attach to the hinge end of swing motion gates. Choose Sliding if you require lateral moving gate automation and Wheeled if you require a motor which utilises a wheeled motor to drive your gate/s.

Motor Voltage

There are two types of power outputs to consider - 24v & 230v. If you need a higher number of operations (opened/closed more than 5-6 times in an hour) during peak periods such as the morning and evening, then you may wish to consider a 24v system.

24v systems are more suitable for higher operation levels as they tend to run cooler than 230v gate motors. However, they do cost more in relative terms, so if you only need to open or close the gate 1-5 times an hour then a 230v system might prove more cost-efficient.

24v motors tend to be used on commercial premises, whereas 230v tend to be used on standard domestic properties. The exception to this rule is sliding gate motors where the reverse is true - 24v sliding gate automation systems tend to be for domestic use, 230v for more intense use (commercial/communal).

24v systems can draw power from battery backup systems meaning they can still operate during any mains power cut (a 230v or 3 phase system would need to be opened with a manual release key).

24v systems can also utilise solar power units as a means of charging batteries, allowing you to site gate automation in rural and remote locations where mains power is unavailable.

Specifications can be found for each product from their datasheet. Each datasheet is downloadable from each product page on this website.

Weight of Gate

All electric gate motors operate up to a maximum weight. This is so the gate will operate in a reliable and safe manner. It is essential to know the weight of each gate leaf in order to choose the correct motor for you installation. If you do not know the weight of your gate/s, send us a photo along with the gate/s dimensions and we can advise.

Gate Width

As with weight, gate motors are designed for gates within certain dimensions. The most important dimension is the width of the gate. To ensure you select the right motor to operate your gate you must know the width of each gate that requires automation.

Opening Angle

Each motor has a maximum angle to which it can operate to. Therefore it is important to note how far the gate needs to open in order for a vehicle to enter/exit safely.

Daily Use

The amount of times your gate is used per day is a determining factor when deciding on the right motor for your usage. Motors are designed to operate within a certain capacity (operations per day) so choosing a motor compatible with your desired use is essential for its durability. Select from the options below the number of times (open & closure = 1 x operation) the gate/s will be operated on an average day.