ASO SENTIR edge 65 ST Safety Edge - 65mm Profile 8.2kΩ

Kit Contents

1 x Length of gate edge safety in 65mm profile

Purchase options for ASO SENTIR edge 65 ST Safety Edge - 65mm Profile 8.2kΩ

Product Details Price Buy
Swing Gate Controller CAT3 2 Channel Controller,8.2Kohm monitoring, 24V- MUST BE USED WITH Q80A PCB £166.79 Add to cart
ASO 65 ST 65mm safety edge - 1000mm 1000m x 65mm GE F-Series - Sentir 65 ST £127.20 Add to cart
ASO 65 ST 65mm safety edge - 1500mm 1500m x 65mm GE F-Series - Sentir 65 ST £146.40 Add to cart
ASO 65 ST 65mm safety edge - 2000mm 2000m x 65mm SENTIR edge F65 ST £164.40 Add to cart
ASO 65 ST 65mm safety edge - 2500mm 2500m x 65mm GE F-Series - Sentir 65 ST £182.40 Add to cart
ASO 65 ST 65mm safety edge - 3000mm 3000m x 65mm GE F-Series - Sentir 65 ST £200.40 Add to cart
ASO 65 ST 65mm safety edge - 3500mm 3500m x 65mm GE F-Series - Sentir 65 ST £218.40 Add to cart
ASO 65 ST 65mm safety edge - 4000mm 4000m x 65mm GE F-Series - Sentir 65 ST £236.40 Add to cart
ASO 65 ST 65mm safety edge - 4500mm 4500m x 65mm GE F-Series - Sentir 65 ST £254.40 Add to cart
ASO 65 ST 65mm safety edge - 5000mm 5000m x 65mm GE F-Series - Sentir 65 ST £272.40 Add to cart
ASO 65 ST 65mm safety edge - 5500mm 5500m x 65mm GE F-Series - Sentir 65 ST £288.00 Add to cart
ASO 65 ST 65mm safety edge - 6000mm 6000m x 65mm GE F-Series - Sentir 65 ST £306.00 Add to cart

 

Please note we cannot offer a next day delivery on this item.

 

For use on sliding gates over 7m

All automatic gates & door systems installed in the UK should comply to BS-EN13241-1 & EN-138491-1 safety standards. ASO safety solutions are Europe’s market leading manufacturer of resistive safety edges and inductive transmitting systems for gates & door systems.


See more information below on the functionality of ASO safety systems and how they comply to the law with examples
of where and how to fit them to automatic gates & doors.

(This information is provided as an introductary guide only. Each individual gate or door installation is unique and a full risk assessment should always be carried out first before any work is undertaken.)

gate safety edge profile

The ingenius design of an ASO Safety Edge comprises of a fully extruded rubber profile with an integrated switching chamber. The switching chamber consists of two conductive rubber surfaces separated by a 4mm void, each surface has a connection wire extruded through its entire length.


A pre-formed plug containing an 8.2kΩ resistor is glued in to one end of the switching chamber penetrating both wires. At the other end a pre-formed wiring plug is glued in to place, again penetrating the chamber wires. This enable monitoring of the entire safety edge.


Finally an end cap is applied at each side to finish the construction of the safety edge. When mounted vertically, the lower end cap has a water drainage seal which needs to be removed to prevent moisture build up. When mounted horizontally, it is recommended that both of the end cap’s seals are removed to ensure no moisture build up.


When the safety edge is connected to its control electronics the system reads the 8.2kΩ resistance. When the safety edge is pressed the two conductive rubber surfaces come together and create a short between them, this cuts the 8.2kΩ signal being monitored by the control electronics.


The control electronics then output a N/C contact or voltage signal (depending on model) to the door or gate control panel.

sliding gate edge safety

Features and Benefits

• Safety edge continuously monitored and tested by electronics.
• Very fast switching time due to fully sealed chamber design.
• One piece construction, no additional chambers or micro switches to install.
• Safety edge sensitive along its entire length.
• EPDM material, highly resistive to environmental corrosion and physical damage.
• Pre-assembled.
• Made to exact length required.
• Safety edge’s certified by a notified body (TUV Nord) to EN1760-2.
• Wide selection of profile sizes to suit any application.

Medium profile  65mm

W: 36.2mm H: 66mm

Material: EPDM

Aluminium Backing Hidden

Got a question about this item?
comments powered by Disqus