Call us on: 01202 717191

FAAC 746 - 230v Sliding Gate Kit

Product Volt Weight
max
per leaf
Angle
max
per leaf
Width
max
per leaf
Type Price Buy
FAAC 746
230v
600 kg
40m
Sliding
£968.00+vat

£1,161.60 inc.vat

Downloads

Kit Contents

1 x FAAC 746 ER Z16
1 x Foundation Plate
2 x 868 Radio Transmitters
1 x Pair XP20 Wireless Photocells
1 x 868 Receiver

Products bought with FAAC 746 - 230v Sliding Gate Kit

 

The FAAC 746 gate kit is for sliding gates with max weight of 600kg. Designed for height and side adjustable fastening.

The control board inside the gear motor facilitates and speeds up installation at a lower cost.

Its compact size makes it ideal for residential applications with gates weighing up to 600kg

Safety is provided by the special, adjustable anti crushing clutch and by an intelligent electronic device which reverses and stops gate movement on obstacle detection.

The 746 performs uniformly with all commands supplied by a safe and reliable microprocessor.

Constant, complete oil-bath lubrication of mechanical components plus assembly in a high resistance pressure-cast aluminium body ensureS a very long life.

As the gear motor is non-reversing no electric locks need be installed.

In the event of power failure the release device, protected by a customised key, makes it possible manually open and close the gate.

 

Technical Specifications of FAAC 746

   
Power supply voltage 230v AC (+6% - 10%)
Power 300w
Current 1.5 A
Thermal protection 120 °C
Thrust 0 to 62.5 daN
Max. weight 600 kg
Use frequency (%) 70
Motor rotation speed 1400 rpm
Operating ambient temperature -20 °C to +55 °C
Dimensions (L x D x H) in mm 275 x 191 x 336
Protection class IP 44
Clutch Twin-disk in oil-bath
Reduction ratio 1:30
Type of oil FAAC HP OIL
Gate speed 9.6 m/min
Limit switch magnetic

Downloads

Kit Contents

1 x FAAC 746 ER Z16
1 x Foundation Plate
2 x 868 Radio Transmitters
1 x Pair XP20 Wireless Photocells
1 x 868 Receiver
Proteco Price Match Promise Order before 3pm Why buy from us? Gate Safe

Gate Automation

Please select what type of automation you require for your gate/s. Double & Single Swing refer to motors which attach to the gate and pillar of a swing motion gate. Double & Single Underground refer to motors which lay beneath the ground which attach to the hinge end of swing motion gates. Choose Sliding if you require lateral moving gate automation and Wheeled if you require a motor which utilises a wheeled motor to drive your gate/s.

Motor Voltage

There are two types of power outputs to consider - 24v & 230v. If you need a higher number of operations (opened/closed more than 5-6 times in an hour) during peak periods such as the morning and evening, then you may wish to consider a 24v system.

24v systems are more suitable for higher operation levels as they tend to run cooler than 230v gate motors. However, they do cost more in relative terms, so if you only need to open or close the gate 1-5 times an hour then a 230v system might prove more cost-efficient.

24v motors tend to be used on commercial premises, whereas 230v tend to be used on standard domestic properties. The exception to this rule is sliding gate motors where the reverse is true - 24v sliding gate automation systems tend to be for domestic use, 230v for more intense use (commercial/communal).

24v systems can draw power from battery backup systems meaning they can still operate during any mains power cut (a 230v or 3 phase system would need to be opened with a manual release key).

24v systems can also utilise solar power units as a means of charging batteries, allowing you to site gate automation in rural and remote locations where mains power is unavailable.

Specifications can be found for each product from their datasheet. Each datasheet is downloadable from each product page on this website.

Weight of Gate

All electric gate motors operate up to a maximum weight. This is so the gate will operate in a reliable and safe manner. It is essential to know the weight of each gate leaf in order to choose the correct motor for you installation. If you do not know the weight of your gate/s, send us a photo along with the gate/s dimensions and we can advise.

Gate Width

As with weight, gate motors are designed for gates within certain dimensions. The most important dimension is the width of the gate. To ensure you select the right motor to operate your gate you must know the width of each gate that requires automation.

Opening Angle

Each motor has a maximum angle to which it can operate to. Therefore it is important to note how far the gate needs to open in order for a vehicle to enter/exit safely.

Daily Use

The amount of times your gate is used per day is a determining factor when deciding on the right motor for your usage. Motors are designed to operate within a certain capacity (operations per day) so choosing a motor compatible with your desired use is essential for its durability. Select from the options below the number of times (open & closure = 1 x operation) the gate/s will be operated on an average day.